In my last post we generated Code coverage statistics for a sample c++. In this post i will be using gcov & lcov to generate similar code coverage for tests in cppagent. To use gcov we first need to compile the source files with
--coverage flag. Our sample c++ program was a single file so it was easy to compile, but for cppagent they use makefiles to build the project. Hence, i started with the Makefile looking for the build instructions.
If my previous posts i discussed the steps for building the agent_test executable, which starts by running make command in test folder. So i started tracing the build steps from the Makefile in test folder. Since we run make without any parameters, the default target is going to be executed.
The first few lines of the file were as below.
# Default target executed when no arguments are given to make. default_target: all .PHONY : default_target
These lines specifies that the default_target for this build is all. On moving down the file we see the rules for all.
# The main all target all: cmake_check_build_system cd /home/subho/work/github/cppagent_new/cppagent && $(CMAKE_COMMAND) -E cmake_progress_start /home/subho/work/github/cppagent_new/cppagent/CMakeFiles /home/subho/work/github/cppagent_new/cppagent/test/CMakeFiles/progress.marks cd /home/subho/work/github/cppagent_new/cppagent && $(MAKE) -f CMakeFiles/Makefile2 test/all $(CMAKE_COMMAND) -E cmake_progress_start /home/subho/work/github/cppagent_new/cppagent/CMakeFiles 0 .PHONY : all
So here in the line
cd /home/subho/work/github/cppagent_new/cppagent && $(MAKE) -f CMakeFiles/Makefile2 test/all
We can see Makefile2 is invoked with target test/all.
In Makefile2 towards the end of the file we can see the test/all target build instructions as,
# Directory level rules for directory test # Convenience name for "all" pass in the directory. test/all: test/CMakeFiles/agent_test.dir/all .PHONY : test/all
The rule says to run the commands defined under target test/CMakeFiles/agent_test.dir/all. These commands are:
test/CMakeFiles/agent_test.dir/all: $(MAKE) -f test/CMakeFiles/agent_test.dir/build.make test/CMakeFiles/agent_test.dir/depend $(MAKE) -f test/CMakeFiles/agent_test.dir/build.make test/CMakeFiles/agent_test.dir/build $(CMAKE_COMMAND) -E cmake_progress_report /home/subho/work/github/cppagent_new/cppagent/CMakeFiles 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 @echo "Built target agent_test" .PHONY : test/CMakeFiles/agent_test.dir/all
The first two lines run the build.make file with target ‘test/CMakeFiles/agent_test.dir/depend‘ and ‘test/CMakeFiles/agent_test.dir/build‘ . The build.make contains all the compile instructions for each of the c++ files. This file is in ‘test/CMakeFiles/agent_test.dir’ folder along with flag.make , link.txt etc files. The flag.make file contains all the compile flags and the ‘link.txt‘ contains the libraries flag needed by linker. On adding the
--coverage flag to these files we can make the c++ source files compile with gcov linked hence .gcno files are generated when the make command is run.
After that we need to run the agent_test as usual. This will create the data files .gcda files. After that we need to gather the .gcda and .gcno files together and run the lcov and genhtml commands and then the html output will be obtained.